OBDSTAR PSA Dash and BSI Odometer Correction Manual

OBDSTAR tools (X300 DP Plus & Odomaster) PSA Peugeot Citroen DS odometer correction vehicle coverage and instructions.

Part 1: Mileage Correction Coverage 

OBDSTAR supports following PSA odometer correction car list:

PEUGEOT
BSI
Auto Select
Manual Select

Continental SC67050 + 95256 CAN (BSI-Q0X-00)
JC easyCAN4F1M-32 + 95128 CAN (BSI04EV-K0X)
JC easyCAN4 + 29LV400BB + 95128 CAN
JC SPC560B60 + 95128 CAN (BSI04EV2-KEX)
SIEMENS 1L00M + 95128/95256 CAN (BSI-S0X)
SIEMENS D76F0018 + 95160 KLINE (BSI-E0X/BSI-F0X)
VALEO SC667152 + 95256 CAN (BSI-N0X)
VALEO 2M48H +24c128 CAN (BSIEV-X0X-00)
VALEO 4L00M + 95128/25128 CAN (BSI2004-P0X-00)

DASHBOARD
Boxer 2015
208
2008
C-ElySee
3008
308 2014-

2008

301
5008
508

CITROEN

BSI
Auto Select
Manual Select

Continental SC67050 + 95256 CAN (BSI-Q0X-00)
JC easyCAN4F1M-32 + 95128 CAN (BSI04EV-K0X)
JC easyCAN4 + 29LV400BB + 95128 CAN
JC SPC560B60 + 95128 CAN (BSI04EV2-KEX)
SIEMENS 1L00M + 95128/95256 CAN (BSI-S0X)
SIEMENS D76F0018 + 95160 KLINE (BSI-E0X/BSI-F0X)
VALEO SC667152 + 95256 CAN (BSI-N0X)
VALEO 2M48H +24c128 CAN (BSIEV-X0X-00)
VALEO 4L00M + 95128/25128 CAN (BSI2004-P0X-00)

DASHBOARD
C3 2009
C3-XR
C4 2010-
C4L
C4 Cactus Mono 2014-
C4 Picasso TFT 2014-
C4 Picasso Mono 2014-
C-Elysee
DS3
DS4
DS5
Jumper 2015

Part 2: OBDSTAR PSA Dashboard and BSI mileage correction manual:

I Both the instrument and BSI support OBD calibration steps:

1.Turn on the ignition

2. Calibrate the instrument, and do not turn off the ignition after completion

3. Calibrate the BSI, and do not turn off the ignition after completion!! Power off the battery for 10 minutes

4. Reconnect the battery negative cable and complete

II. Steps of onty BSI supporting the OBD calibration:

1. Remove the instrument and use the programmer to calibrate it

2. Turn on the ignition and calibrate the BSI. Do not turn off the ignition after completion!! Power
off the battery for 10 minutes.

3. Put the instrument back into the vehicle

4. Reconnect the battery negative cable and complete

Note:

1. During the mileage adjustment process, ensure that the power is sufficient and the voltage is stable;
2. Before performing the adjustment, you must first read and save the instrument and BSI data (EEPROM and FLASH);
3. For the mileage reset, it needs to adjust the instrument and BSI module at the same time. If one of them is adjusted first, it will be synchronized by the data of another module and restored to the original mileage. The solution is as follows:

Method  1:

First remove the adjustment, do not pull the plug, and then adjust the instrument mileage through OBD. After the adjustment is successful, immediately unplug the instrument (as fast as possible), and then adjust the BSI mileage through OBD. The value is consistent with the instrument. After that, enter the reading mileage, confirm the mileage to be adjusted, and then install the instrument;

Method 2:

First adjust the instrument mileage through OBD. After the adjustment is successful, immediately unplug the instrument power supply fuse (as fast as possible, it is recommended to unplug the fuse before adjusting the instrument to check whether the instrument is powered off), and then adjust the BSI mileage through OBD. The value is consistent with the instrument. After that, enter the reading mileage, confirm the mileage to be adjusted, and then install the instrument fuse;

The instrument fuse is on the BSI, and the BSI position is generally below the steering wheel, as shown below.

Note: The position of the fuses may vary depending on years and models. According to the BSI module brand type, Valeo is generally F21, Continent is generally F19, and JOHNSON CONTROLS is generally F12…;

BSI menu is based on types, such as “CONTINENTAL BSI-Q0X”, where CONTINENTAL is the BSI brand name, Q0X is the BSI type, X stands for any number 0-9, the device can automatically recognize, if not, the types are not supported. Types can be seen on the BSI module label, as shown below.

Users can check PSA odometer Help menu in OBDSTAR X300 DP Plus tablet as well.

www.obdii365.com