Audi Q5, A6, A8 Hybrid Battery Repair with OBDSTAR P50

 Audi Q5, A6, A8 hybrid P1609 crash shut-down problem can be solved by OBDSTAR P50. 

Processor:

8R0915591  8R0 915 591

8R0915223  8R0.915.233

Problems:

•     Engine don't start.
•     Hybrid system is locked.

Battery Energy Control Module (Hybrid Battery Module)

Possible Causes

•     Crash Signal activated (i.e. Accident with Airbag Deployment)

Fault Code

• 14806 - Crash Shut-Down Activated
• P1609 00 [039] - -

No need to replace battery. Two solutions.

1.ODIS. 

Restart High Voltage system.  First you need to remove crash data from the airbag module and then with odis you can disable the protection in the battery.

2. with OBDSTAR P50

OBDSTAR P50 will reset and repair 8R0915591 and 8R0915223 processor on bench. 

OBDSTAR P50 Reset Audi Battery on Bench

 OBDSTAR P50 released new battery reset software version V30.06 on June 27th, 2023. 

Add Audi BMS 8R0915233, 8R0915591 crash record erase and repair(on BENCH)

In Audi A6, A8 and 05 hybrids, the hybrid battery management unit (BMS) disconnects and logs a P1609 fault code when a crash occurs (!!! Crash shut-down activated !!!). resulting in the vehicle not starting.
At present, only a few auto electronic repair professionals through the brush firmware or open the cover through the programmer to repair  (high cost. risky. and only support some models), our company free upgrade P50 battery module repair function again. 
P50 supports the BMS crash record (P1609) repair function (on BENCH) for the 8R0915233 and 8R0915591 parts, no need to disassemble and read the chip, no n$k and difficulty, which can save a lot of maintenance costs.

OBDSTAR DC706 Adds GPEC2 GPEC3 GPEC4 in Boot

 OBDSTAR DC706 ecu flasher released an important update in May 2023- Adding GPEC2, GPEC2A, GPEC3 and GPEC4 read and write in boot mode.

No more flex, hptuner or dimsport, dc706 can do it yourself, full reading and writing.

 

V30.08 software adds the following GPEC types:

CHRYSLER CONTINENTAL GPEC2 MPC5566+95320
CHRYSLER CONTINENTAL GPEC2A MPC5674F+25320
CHRYSLER CONTINENTAL GPEC3 MPC5674F
DODGE CONTINENTAL GPEC2 MPC5566+95320
DODGE CONTINENTAL GPEC2A MPC5674F+25320
DODGE CONTINENTAL GPEC3 MPC5674F
FIAT CONTINENTAL GPEC2 MPC5566+95320
FIAT CONTINENTAL GPEC3 MPC5674F
JEEP CONTINENTAL GPEC2 MPC5566+95320
JEEP CONTINENTAL GPEC2A MPC5674F+25320
JEEP CONTINENTAL GPEC3 MPC5674F
JEEP CONTINENTAL GPEC4 MPC5674F+25320
LANCIA CONTINENTAL GPEC2 MPC5566+95320
VOLKSWAGEN(VW) CONTINENTAL GPEC2 MPC5566+95320

 

Function:
Read eeprom/dflash
Read flash
Write flash
Read showflash (except VW GPEC2)

*DC706 will clone these GPEC ECUs but not unlock them.

DC706 will show you the wiring diagram and instructions.  P003 adapter is required to clone GPEC series.

 

For example

OBDSTAR DC706 read/write GPEC2 in boot

DC706 also read 7G 8GF 9GF 10GF, GM T87, T8A and much more ECU/TCUs which were only available for Flex, B-flash etc. Now you can do it by DC706.
More updates coming- EMS3110, EMS3120, EMS3125 from Renault.